SD003-PCR-LA (Quick Immunity Sequencer) – Updater

未設定メニュー

SD003-PCR-LA (Quick Immunity Sequencer) Updater

This software is to update the application version of the SD003-PCR-LA for power line disturbance immunity testing.

Ver.

1.13.00

Last update

2015/7/23

Configuration

  • Vista(x86/x64)
  • 7(x86/x64)
  • 8(x86/x64)
  • GPIB RS232C

Download

Release Note

VER 1.13
2015-7-16

IEC61000-4-29

Resolved issues
There was a problem in which sometimes High-impedance / Low-impedance of "DC short interruption" was not output as configured.
Resolved issues
When "Run" was carried out several times in output ON, there was a problem in which interruption of setting become rarely longer than its configuration.
VER 1.12
2013-12-16

IEC61000-4-29

Resolved issues
There was a problem in which interval time was longer for 0.001 second than the setup time when repeating.
VER 1.11
2013-4-02

IEC61000-4-28

Resolved issues
At f1+Delta f, there was a problem in which minus value was out of range. This problem occurred only by Ver1.10.
VER 1.10
2013-5-25

IEC61000-4-28

Resolved issues
There was a problem in which a command error occurred when the value of more than 999.999 seconds was set.
VER 1.09
2012-2-17

Quick Immunity Sequencer

Resolved issues
There was a problem that runtime was insufficient in the installer. This problem occurred only by Ver1.08.
VER 1.08
2011-1-01

IEC61000-4-13

Resolved issues
We corrected a problem of effective value of the output voltage being different which was caused by the fact that we were not converting the voltage distortion factor due to the superimposed harmonics by Over swing, Sweep in frequency, Odd non multiple of 3, Odd multiple of 3 and Even harmonics.
VER 1.07
2009-11-30

IEC61000-4-13

Resolved issues
At Flat curve, there was a problem that Ver1.0.6 generated overshoots and undershoots when switching between banks.
VER 1.06
2009-11-12

IEC61000-4-13

Resolved issues
There was a problem that Level 0.80 required by Flat Curve Class 3, could not be set under the three-phase system.
Resolved issues
At Flat Curve under the three-phase system, the output waveform has been corrected from "line-to-line" peak-clip to "inter-phase" peak-clip.
VER 1.05
2009-4-08

Quick Immunity Sequencer

Resolved issues
When using in European region where "comma" is used as the decimal point, there was a problem that the error message "x.xx is not a valid float" was not correctly shown.
VER 1.04
2007-6-04

Quick Immunity Sequencer

Resolved issues
There was a problem that unwanted phase-shifting was generated when using IT01.
Resolved issues
There was a problem that unexpected "End" could be detected before sequence start after operating Send → Run.
Resolved issues
When launching at the condition of "Not use IT01", changing between "Use IT01" and "Not use IT01" caused a communication error.
Resolved issues
There was a problem that communication errors caused unwanted application's abortion.
VER 1.02
2005-5-13

Quick Immunity Sequencer

Resolved issues
There was a problem that send operation caused hang-up after switching "Use IT01" to "Not use IT01".
VER 1.00
2004-4-07

Quick Immunity Sequencer

New Feature
The first release

如有任何问题或担忧,请与我们联系。

下载产品目录 产品目录
采购考虑/报价要求 Contact Us
close

Search